The Triplett Model MM650 is a 6000 count high performance digital multimeter with True RMS readings to provide better accuracy when measuring non-sinusoidal or noisy waveforms. Read More >

DESCRIPTION

The Triplett Model MM650 is a 6000 count high performance digital multimeter with True RMS readings to provide better accuracy when measuring non-sinusoidal or noisy waveforms. It offers a large variety of measurement features including AC/DC Voltage, AC/DC Current, AC/DC µA Current, Resistance, Temperature, Frequency, Capacitance, Continuity, and Diode Test. Additional features include 61-segment analog bargraph, backlit LCD, buttons and switch selector, Lo Z (impedance) mode for identifying ghost voltages, data hold, peak hold, relative mode, and a built-in flashlight. The rubberized overmolded housing provides impact and drop resistance in a sleek ergonomic design that is also waterproof (IP67). CAT IV 600V safety rating provides superior resistance to damage from transient overvoltages in any demanding industrial settings. The Model MM650 is suited for a variety of industrial and residential applications such as security, home theater, electrical, HVAC installations and more. Includes test leads, temperature probe, (4) AAA batteries, and carrying case. 3-year warranty.

MM650-NIST Comes with Certificate of traceability to NIST standards
Please add 11 business days lead-time for the NIST calibration process

CATEGORY: DIGITAL MULTIMETER

Features

True RMS provides better accuracy when measuring non-sinusoidal or noisy waveforms
Measures AC/DC Voltage and Current, Resistance, Temperature, Capacitance, Frequency, Diode and Continuity
µA Current measurement
Low input impedance (Lo Z) mode for ACV/DCV measurements
Peak Hold
Backlit LCD, Buttons, and Switch Selector
Data Hold and Relative mode
Waterproof (IP67)
Built-in Flashlight
Includes test leads, temperature probe, (4) AAA batteries, and carrying case

Specifications

Resistance	60MΩ
Temperature	-4 to 1400°F (-20 to 760°C)
Capacitance	6000µF
Frequency	10kHz
Duty Cycle	20 to 80%
Low impedance (Lo Z) Mode	Yes
Power	(4) AAA batteries
Waterproof	IP67
Safety Category	CAT IV-600V
Dimensions	6.7 x 3 x 1.9" (170 x 75 x 48mm)
Weight	13.6oz. (386g)

Downloads

Datasheet
User Manual

Description

The Triplett Model TEV200 Electric Vehicle Probe Kit plugs directly into your Digital Multimeter, Clamp Meter or Multifunction Tester (MFT) and allows you to perform typical measurements: voltage, frequency, phase indication, phase sequence, various RCD tests, insulation resistance, low ohm measurements, line and loop impedances (if supported by the measuring input device). It easily connects by wire (Standard Male Banana Type) between the EVSE charging point (Type-2 connector) and the measurement inputs of the DMM, Clamp or MFT. All wires of the charging connector are available: L1, L2, L3, N, PE, CP and PP. The built-In Control Pilot (CP) State (Vehicle Simulation Switch) can simulate vehicle states with different resistances connected between CP and PE conductors. You can use the CP Signal output terminals to connect your oscilloscope to check the waveform and amplitude of the CP signal. CP Error “E” simulates the behavior of the station when there is an established short circuit between CP and PE. The Probe Kit complies with EMC Directive (2014/30/EU), the Low Voltage Directive (2014/35/EU), and EN61010-1 standards. Includes (1) IEC62196-2 Type 1 female to male adaptor/converter and pouch case.

CATEGORY: EV Charging Station Testers

Features

Plugs directly into your Digital Multimeter (DMM), Clamp Meter or Multifunction Tester (MFT)
Simply connects by wire (Standard Male Banana Type) between the EVSE charging point (Type-2 connector) and the measurement inputs of the DMM, Clamp or MFT. All wires of the charging connector are available: L1, L2, L3, N, PE, CP and PP
Allows you to perform typical measurements: voltage, frequency, phase indication, phase sequence, various RCD tests, insulation resistance, low ohm measurements, line and loop impedances (If supported by the measuring input device)
Built-In Control Pilot (CP) State (Vehicle Simulation Switch) - Different vehicle states can be simulated: Vehicle states are simulated with different resistances connected between CP and PE conductors
CP Signal output terminals - Use an oscilloscope to check the waveform and amplitude of the CP signal
CP Error “E” simulation: Simulate the behavior of the station when there is an established short circuit between CP and PE
Complies with EMC Directive (2014/30/EU), the Low Voltage Directive (2014/35/EU), and EN61010-1 standards
Includes: (1) IEC62196-2 Type 1 female to male adaptor/converter and pouch case2196-2 Type 1 female to male adaptor/converter and pouch case

Specifications

	TEV200
Input Voltage	230/400V 3 phase 50/60 Hz
CP Simulation	States A, B, C
PP Simulation	Setup internally to 20 A
Error Simulation	CP error “E”, PE (Earth Fault) Error
Measurement Category	CAT II 300 V
Mains Socket Rating	Maz 10A
Test Connector Type	IEC62196-2 Type 1 male (Male to Female Adaptor Included/Tesla)
Test Cable Length	19.7” (0.5m)
Power	Powered by Charging System
Dimensions	7.7”x 4.2” (6x 60mm)
Weight	14.0oz (396g)

	Control Pilot (CP)State (Vehicle Simulation)
Vehicle State	State Description	CP/PE Resistance	Vehicle State
A	Electric vehicle not connected	open (∞)	±12V @ 1KHz
B	Electric vehicle connected, not ready to charge	2.74 K	+9V/-12V@1KHz
C	Electric vehicle connected, ready to charge, ventilation not required	882Ω	+6V/-12 @ 1KHz
E	CP Error	0Ω	0V


	TEV200
Input voltage	UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 208 V, 60 Hz (three-phase system) or UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 240 V, 60 Hz (single-phase system), ±10% voltage fluctuations from nominal
EV connector (EVC-13)	SAE J1772 (Type 1, 5P single phase) for measuring purpose Adapter SAEJ1772 to NACS for measurement purpose
Internal power consumption	n.a.
Operating temperature	-20 to 40 degree C (-4 to 104F)
Storage temperature	-20 to 40 degree C (-4 to 104F)
Operating Altitude	2000 mtr
Weight	tbd
Safety standards	IEC 61010-1, Pollution Degree 2
	IEC61010-031
Measurement category	CAT II 300V
IP protection class	IP40
Functions
Indication LEDs	n.a.
CP States	A, B, C
CP Error “E”	On / Off
PE Error	n.a.
GFCI Test	n.a.
PE Pre-Test (typical)	n.a.
Outputs (for test purpose only)
Measuring terminals	Max. 250 V 50/60 Hz, CAT II 300 V
L1, L2/N, PE
CP signal output terminals	Approx. ±12 V (under normal conditions), in case of wrong wiring or error of the charging station these terminals can be hazardous ≥ max. 250 V against PE

Downloads

Datasheet
User Manual

Country

Country

Electric Vehicle Probe Kit (TEV200)